Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Littleton: What to Know First
We provide independent Abatement Technologies HVAC cleaning in Littleton for homeowners who want the work documented, not guessed at. Most Abatement Technologies systems we service in Littleton - the HEPA-AIRE and Predator series are common here - are completed in a single scheduled visit with a written price agreed before we touch a panel. A typical evaporator coil and blower cleaning runs $340-$520 for a standard residential air handler, and every job ships with before-and-after photos of every component we accessed.
This page is for Abatement Technologies owners in Littleton, Columbine Knolls, and the broader Arapahoe County area who’ve noticed weak airflow, ice on the coil, or a blower that sounds like it’s working harder than it should. If that’s your situation, call (720) 315-7291. We’ll send a written estimate you can compare against any other.
How Abatement Technologies Products Fail - and How We Fix Them
- Predator 1200 series blowers: bearing wear from fine dust bypass. The sealed bearing housing on these units sits close to the motor mount, and when the pre-filter media loads up in Littleton’s dry spring dust season, particulate gets pulled past the seal. We pull the blower assembly, photograph the bearing race condition, and replace with OEM or SKF-equivalent bearings - not generic hardware-store units that throw the balance off. The fix holds because we clean the full return path, not just the blower cage.
- HEPA-AIRE portable units: clogged evaporator fins in high-altitude operation. Littleton’s 5,400-foot elevation means lower air density, so these units run higher CFM per ton to hit rated capacity. That pulls more debris through the coil fins, especially in homes near the South Platte where cottonwood seed is heavy in June. We use low-pressure foaming cleaner and a fin comb set specific to Abatement Technologies spacing - 8 fins per inch on the HA500 series - rather than pressure-washing, which folds the aluminum and voids the warranty.
- Predator 600 air handlers: heat exchanger soot staining from incomplete combustion. These units show up in Littleton basements installed by builders who sized for sea-level BTU ratings. The induced-draft motor works harder, the flame pattern drifts, and the crimp-ring heat exchanger collects carbon at the upper bends. We scope every chamber with a bore camera, document the staining pattern, and clean with a soft-bristle rotary tool - never wire brushes that score the aluminized steel and create failure points.
- HEPA-AIRE H5000 series: blower belt glazing from static pressure mismatch. Abatement Technologies specs a 3/8-inch AX belt on these units, but Littleton’s tighter building envelopes and added MERV-13 filters push static past design. The belt slips, glazes, and throws rubber dust into the cabinet. We measure actual static pressure across the filter and coil, then spec the correct belt tension and pitch - sometimes moving to a cogged AX belt if the load is persistent. We show you the gauge reading, not just the new belt.
- Predator 2400 commercial-grade coils: formicary corrosion from condensate chemistry. The copper tube-and-fin coils in these larger units react with certain VOC off-gassing from newer flooring and cabinetry - common in Littleton homes built 2018-2023. The corrosion tunnels under the fin collar, invisible until pressure loss shows up. We pressure-test the refrigerant circuit, photograph any fin lift or tube discoloration, and treat with an OEM-approved epoxy coating if the leak is pinhole and localized. Replacement gets quoted separately with the part number in writing.
Our Abatement Technologies HVAC Cleaning Process
- 1
Inspection with documentation. We access the air handler cabinet, evaporator compartment, and blower housing, then run a bore camera through every component. The camera doesn’t negotiate - it just shows what’s there. You get the footage before we quote.
- 2
Written scope and price. Haven Standard Clause 1: the price is written, line-itemed, and agreed before work starts. No per-vent add-ons, no “we found something else.” The number on the page is the number on the invoice.
- 3
Component-specific cleaning protocol. Abatement Technologies coils get foaming cleaner matched to their fin geometry; blowers get removed and cleaned on a bench to protect the motor seals; heat exchangers get scoped and brushed per manufacturer tolerance. We use Abatement Technologies-compatible tools - not generic attachments forced to fit.
- 4
Parts decision documented. If a bearing, belt, or seal needs replacement, we note OEM versus quality aftermarket options with part numbers and warranty terms. You choose; we record it in the job file.
- 5
Post-clean test and photo record. We measure static pressure, temperature split, and amp draw against the Abatement Technologies spec sheet for your model. Then we photograph every cleaned component and deliver the set as a standard job record - Haven Standard Clause 5.
- 6
365-Day Done Right Promise activation. The written guarantee goes into your file. If airflow, noise, or temperature split drifts in the next year, we return and make it right.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Littleton
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning (HEPA-AIRE / Predator residential) | $340-$520 | Coil accessibility (horizontal vs. vertical air handler), fin corrosion severity, refrigerant isolation required |
| Blower assembly removal and cleaning | $280-$410 | Bearing condition, cage balance issues, motor electrical testing |
| Condenser coil cleaning (outdoor unit) | $220-$340 | Fins per inch density, debris type (cottonwood seed vs. standard dust), straightening needed |
| Heat exchanger inspection and cleaning | $380-$590 | Number of chambers, soot level, camera access path |
| Full system HVAC cleaning (coil, blower, condenser, heat exchanger) | $890-$1,340 | System tonnage, component count, parts replacement needed |
Price drivers we see in Littleton: homes near the Hogback or in Ken Caryl Valley get more wind-blown debris through outdoor coils; older Columbine Knolls installations often need extra access panel work to reach the evaporator. We note these in the written scope, not as surprise add-ons.
Every estimate is free. Call (720) 315-7291 and we’ll put a written number next to any competitor’s quote - Haven Standard Clause 7, Free Second Opinion.
Why Littleton Homeowners Call CleanRun Air Duct Cleaning Littleton for Abatement Technologies Work
We’ve cleaned Abatement Technologies equipment in Littleton since 2013 - over 52,000 homes served, every one with a written price first and a photo record at the end. Tomas Reyes, our owner, pulls the inspection camera before quoting anything and walks you through what it shows: debris load, fin condition, seal gaps. No sales language.
Our crew knows Abatement Technologies specs because we document them - fin counts, bearing tolerances, belt sizes - and we stock parts for the Predator and HEPA-AIRE lines most common in this market. When we encounter Lennox, Trane, or Carrier systems in the same home (common in Littleton additions and retrofits), we service those with the same protocol and documentation standard.
The 365-Day Done Right Promise is in writing on every job. The photo record is standard, not an upgrade. And the price is flat per system, not per vent, not per hour. That’s Haven Standard.
FAQs
No - independent service does not void your Abatement Technologies warranty, provided the work follows manufacturer specifications for cleaning agents, pressure limits, and component handling. We document our methods against those specs and include the reference in your job file. If you have a current warranty claim in progress, call (720) 315-7291 and we’ll coordinate with your documentation.
The bore camera shows the difference: cleaning addresses surface debris and light corrosion; replacement is needed when fin separation exceeds 20 percent or tube leaks are confirmed with a nitrogen pressure test. We show you both findings and quote each path in writing. Call (720) 315-7291 for a free inspection.
OEM parts match the original specification exactly; quality aftermarket parts from SKF, Gates, or equivalent meet the same tolerances and often carry comparable warranties. We quote both with part numbers and let you choose, documented in the scope. For warranty-active systems, OEM may be required - we note this when it applies.
Every 3-5 years for typical residential use; every 2-3 years if you have pets, recent renovation, or live near active construction in areas like Sterling Ranch or Crystal Valley. Littleton’s dry climate and seasonal dust events load filters faster than coastal markets. We include a recommended interval in your post-job report based on what the camera found.
Yes - we clean and inspect Predator 2400 and H5000 series units in light commercial applications throughout Littleton and Arapahoe County. These jobs require scheduled access windows and may need refrigerant recovery; we quote that scope separately with the recovery protocol noted. Call (720) 315-7291 to schedule a site visit.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Littleton at CleanRun Air Duct Cleaning Littleton, serving Littleton and nearby areas.